Step 2c: Setup Using the Command Line Interface

The CLI setup wizard allows you to quickly configure your Unleashed Master AP with basic settings using a short series of CLI commands.

To perform Unleashed setup using CLI commands, use the following procedure:

  1. When the Unleashed AP is in factory default state, associate to the "Configure.Me-xxxxxx" WLAN and connect to the Unleashed CLI using SSH (default IP address: unleashed.ruckuswireless.com or 10.154.231.125), and log in using the default user name and password:
    • Please login: super
    • Password: sp-admin
    NOTE
    For information on using the Unleashed CLI, see the Unleashed Command Line Interface Reference Guide, available from support.ruckuswireless.com.
    The Unleashed CLI Wizard Configuration Tool starts automatically.
  2. Follow the instructions in the setup wizard to configure your Unleashed Master AP. The following are two examples.
    Configure Unleashed AP to Bridge Mode
    Please login: super
    Password: ********
    
    
    Welcome to Ruckus Wireless Unleashed CLI Setup Wizard 
    
    
    Would you like to start the Setup Wizard? [yes/no]: yes
    
    Enter Administrative User Name (32 characters max) [admin]: 
    admin
    Enter Administrator Password (4-32 characters): 
    *****
    Re-enter Administrator Password (4-32 characters): 
    *****
    
    Enter System Name (32 characters max) [Ruckus-Unleashed]: 
    Unleashed
    
    Enter Country Code (or 'help' to show the list) [US]: US
    
    Enable Mesh [yes/NO]? no
    
    Enable Gateway Mode [yes/NO]? no
    
    Enter WAN IP type [1]: 
         1: DHCP Mode;
         2: Manual Mode;
    1
    
    Enable WLANs [YES/no]? yes
    
    Enter Wireless LAN (ESSID, 1-32 characters) [Ruckus-Wireless 1]: 
    Unleashed-SSID
    Is it an Open WLAN [yes/NO]? no
    Enter the WPA2 Passphrase (8-63 characters): ********
    Re-enter the WPA2 Passphrase (8-63 characters): 
    ********
    
    Please review the following settings:
    System Name=                Unleashed
    Administrator Name=         admin
    Country Code=               US
    Mesh Supported=             Disable
    Gateway Mode Supported=     Disable
    IPv4 Mode=                  DHCP
    WLAN ESSID=                 Unleashed-SSID
    Wireless Authentication=    WPA2_PSK
    
    
    Done with the Setup Wizard [yes/no]? yes
    
    Save the configuration ...  
    
    
    
    It will take a few minutes to complete, do not power off the AP! This AP will reboot automatically. 
    
    Welcome to Ruckus Unleashed Network Command Line Interface
    ruckus>
     
    
    Configure Unleashed AP to Gateway Mode
    Please login: super
    Password: ********
    
    
    Welcome to Ruckus Wireless Unleashed CLI Setup Wizard 
    
    
    Would you like to start the Setup Wizard? [yes/no]: yes
    
    Enter Administrative User Name (32 characters max) [admin]: 
    admin
    Enter Administrator Password (4-32 characters): 
    *****
    Re-enter Administrator Password (4-32 characters): 
    *****
    
    Enter System Name (32 characters max) [Ruckus-Unleashed]: 
    Unleashed-Gateway
    
    Enter Country Code (or 'help' to show the list) [US]: US
    
    Enable Mesh [yes/NO]? no
    
    Enable Gateway Mode [yes/NO]? yes
    
    Enter AP R510 WAN Port: 
        1: port1, eth0, UP: 
        2: port2, eth1, DOWN: 
    1
    
    Enter WAN IP type [1]: 
         1: DHCP Mode;
         2: Manual Mode;
         3: PPPOE Mode;
    1
    
    Enter LAN & WLAN IP Address [10.106.0.1]: 
    192.168.1.1
    Enter LAN & WLAN IP Netmask [255.255.0.0]: 
    255.255.255.0
    Enter Client Starting IP Address [10.106.0.2]: 
    192.168.1.2
    Enter Client Ending IP Address [10.106.7.209]: 
    192.168.1.200
    
    Enter Lease Time [2]:
        1: 6 hours;
        2: 12 hours;
        3: 1 day;
        4: 2 days;
        5: 1 week;
        6: 2 weeks;
    
    1
    
    Enable WLANs [YES/no]? yes
    
    Enter Wireless LAN (ESSID, 1-32 characters) [Ruckus-Wireless 1]: 
    Unleashed-SSID
    Is it an Open WLAN [yes/NO]? no
    Enter the WPA2 Passphrase (8-63 characters): 
    ********
    Re-enter the WPA2 Passphrase (8-63 characters): 
    ********
    
    Please review the following settings:
    System Name=                Unleashed-Gateway
    Administrator Name=         admin
    Country Code=               US
    Mesh Supported=             Disable
    Gateway Mode Supported=     Enable
    WAN Port=                   port1 eth0 UP
    IPv4 Mode=                  DHCP
    LAN Port IPv4 Address Info= 192.168.1.1/255.255.255.0
    Client Starting IPv4=       192.168.1.2
    Client Ending IPv4=         192.168.1.200
    Lease Time=                 6 hours
    WLAN ESSID=                 Unleashed-SSID
    Wireless Authentication=    WPA2_PSK
    
    
    Done with the Setup Wizard [yes/no]? yes
    
    Save the configuration ...  
    
    
    
    It will take a few minutes to complete, do not power off the AP! This AP will reboot automatically. 
    
    Welcome to Ruckus Unleashed Network Command Line Interface
    ruckus>