What's new in this document
Information has been added or updated to reflect new FastIron features or enhancements to existing FastIron features.
For commands introduced since Release 08.0.01, a history table listed with each command provides information about modifications to the command. For commands introduced prior to Release 08.0.01, a history table is not provided, unless the command has been modified in recent releases.
NOTE
In addition to commands that are new or modified for this release, numerous commands for existing FastIron features have been added that were previously described only in FastIron configuration guides.
New commands in FastIron 08.0.50
The following commands have been added (new for this release).
- aaa accounting mac-auth
- authentication (IKEv2)
- clear ikev2 sa
- clear ikev2 statistics
- clear ipsec sa
- default-ipv6 gateway
- description (IKEv2)
- description (IPsec)
- dhcp snooping relay information circuit-id
- dhcp snooping relay information remote-id
- dhgroup
- encapsulation-mode
- encryption
- encryption-algorithm
- ike-profile
- ikev2 auth-proposal
- ikev2 exchange-max-time
- ikev2 limit
- ikev2 policy
- ikev2 profile
- ikev2 proposal
- ikev2 retransmit-interval
- ikev2 retry-count
- initial-contact-payload
- integrity
- ipsec profile
- ipsec proposal
- ipv6 default gateway
- issu abort
- issu primary
- issu secondary
- keepalive (IKEv2)
- lifetime (IKEv2)
- lifetime (IPsec)
- lldp advertise port-id-subtype
- local-identifier
- logging enable ikev2
- logging enable ipsec
- match address-local
- match fvrf
- match-identity
- multicast querier-address
- multicast6 querier-address
- prf
- proposal (IKEv2)
- proposal (IPsec)
- protected
- radius-server accounting
- radius-server test
- remote-identifier
- responder only
- set next-hop-ip-tunnel
- show ikev2
- show ikev2 auth-proposal
- show ikev2 policy
- show ikev2 profile
- show ikev2 proposal
- show ikev2 sa
- show ikev2 session
- show ikev2 statistics
- show inline power debug-info
- show inline power emesg
- show ip dhcp relay information
- show ip dhcp relay information brief
- show ipsec card-utilization
- show ipsec profile
- show ipsec proposal
- show ipsec sa
- show issu errors
- show issu sequence
- show issu status
- show module
- show running ikev2
- show spx connections
- show spx-mon
- show tech-support
- spx allow-pe-movement
- spx interactive-setup
- spx zero-touch-deny
- spx-mon enable
- transform
- trunk-type
- vlan-config
- zero-touch-enable
- zero-touch-ports
Modified commands in FastIron 08.0.50
The following commands have been modified in this release.
- aaa authorization coa ignore
- clock summer-time
- clock timezone
- ip address
- ip dhcp-client discovery-interval
- ip dscp-remark
- multi-spx-lag
- multi-spx-port
- pvlan type
- radius-server dead-time
- radius-server host
- set ip next-hop
- show clock
- show cpu-utilization
- show dot1x ip-acl
- show dot1x sessions
- show inline power
- show inline power detail
- show ip vrrp-extended
- show lag
- show mac-authentication ip-acl
- show mac-authentication sessions
- show spx
- show statistics tunnel
- show vlan
- spx cb-configure
- spx unconfigure
Deprecated commands in FastIron 08.0.50
The following commands have been removed:
- priority ignore-8021p (not supported on ICX 7000 series devices)
- protected-link-group (not supported on ICX 7000 series devices)
- show protected-link-group (not supported on ICX 7000 series devices)